U2024-87 Jeep Code — Meaning, Causes, Symptoms & Fix

What Does U2024-87 Mean?

The U2024-87 diagnostic trouble code is a high severity issue specifically indicating a missing message. In most Jeep models, this is primarily caused by a a module sending missing message. Because drivability is limited, you should address this promptly. Expected repair costs typically range from $100 to $1200. Your first diagnostic step should be to perform a full network scan to identify which modules are offline or reporting errors.

When your Jeep's Engine Control Module (ECM) detects an anomaly in the advanced network communication, it triggers the U2024-87 code. Specifically, the ECM continuously monitors the vehicle communication network for proper voltage and resistance. The module continuously monitors the network for expected messages. If messages are missing, invalid, or the bus drops offline, this code is set. In the context of Jeep vehicles, In Jeep vehicles, network codes often point to TIPM (Totally Integrated Power Module) issues, wiring harness chafing, or water intrusion in specific modules (like blind spot or sway bar disconnect). This means the can bus / control modules is no longer operating within factory specifications, compromising overall system efficiency.

At its core, the U2024-87 code means the powertrain computer has seen data outside of its programmed parameters. The extension indicates a missing message. Specific failure condition: Missing Message detected. In real-world driving, Depending on the affected module, you may experience warning lights, loss of specific features (like cruise control or ABS), or a complete no-start condition. Ignoring this signal can lead to cascading failures in related emissions or engine timing components.

The module continuously monitors the network for expected messages. If messages are missing, invalid, or the bus drops offline, this code is set.

In Jeep vehicles, network codes often point to TIPM (Totally Integrated Power Module) issues, wiring harness chafing, or water intrusion in specific modules (like blind spot or sway bar disconnect).

Symptoms of U2024-87

When this code is active, you may notice:

• Multiple Warning Lights (High): Key ON
• Loss of Specific Vehicle Features (Medium): While driving
• Possible No-Start Condition (Critical): If PCM/TCM communication is lost

Common Causes of U2024-87

Ranked most to least likely:

1. Corroded or Loose Connectors (Most Common)
2. Failed Control Module (Common)
3. Wiring Harness Damage (Short/Open) (Possible)
4. Low Battery Voltage (Common)

Most likely cause: a module sending missing message

Step-by-Step Diagnosis

Follow these steps in order:

1. Battery & Charging System Test: Verify battery voltage is above 12.4V. Low voltage is a primary cause of false network codes. Expected: Battery passes load test.
2. Full Network Scan: Use an advanced diagnostic scanner to ping all modules on the CAN bus. Expected: Identify which modules are offline or reporting the code.
3. Visual Inspection: Inspect wiring harnesses and connectors at the affected module for water intrusion or damage. Expected: Connectors are clean, dry, and secure.

First step: perform a full network scan to identify which modules are offline or reporting errors

How to Fix U2024-87

Clear Codes and Reset Network

DIY Difficulty: 2/5. Labor: 0.5 hours. Perform a battery hard reset (disconnect negative terminal for 15 mins) and clear codes to see if the fault returns.

Repair Wiring/Connector

DIY Difficulty: 6/5. Labor: 1-3 hours. Clean corroded pins, replace damaged connector pigtails, or repair chafed wiring.

Replace Faulty Module

DIY Difficulty: 8/5. Labor: 1-4 hours. Parts: Control Module. Replace the failed module. Note: Most modules require dealer-level programming/flashing after installation.

Depending on the affected module, you may experience warning lights, loss of specific features (like cruise control or ABS), or a complete no-start condition.

Repair Cost Breakdown

Estimated costs for fixing U2024-87:

Typical cost range: $100 to $1200

Is It Safe to Drive with U2024-87?

Use caution driving with U2024-87. Severity is High. This could be a minor sensor fault or a more serious mechanical problem requiring immediate attention.

If you experience drivability symptoms (rough idle, stalling, loss of power), stop immediately. With no symptoms, drive conservatively and book a diagnostic appointment soon.

Affected Jeep Models

• Various Jeep Models (2007-Present) [JK, JL, WK2, KL]: Network codes are universal across modern CAN-equipped Jeeps.

Real-World Fixes

• NetworkDiagTech: Performed full system scan, found low voltage history. Replaced weak battery and cleared codes. Result: Network communication restored, codes did not return.

Frequently Asked Questions

Q: What does the U2024-87 code mean?

A: The module has detected a network communication issue (U2024) specifically characterized by a missing message (suffix -87). This indicates a specific failure in data transmission or module response on the CAN bus.

Q: Can a bad battery cause U-series codes?

A: Yes. Modern Jeeps are highly sensitive to voltage drops. A weak battery can cause modules to temporarily drop offline, triggering network codes.